Wiring Schematic Diagram

The 1996 Suzuki Esteem Cooling Fan system consists of control relay for: radiator fan (located in relay box), air conditioning fan motor, radiator fan motor, condenser fan motor, junction box, fuse and relay box, engine control module. The following circuit diagram and wiring diagram / schematic shows 1996 Suzuki Esteem Cooling Fan system. (click image to enlarge) 

This wiring diagram is a simplified of the 1963 Ford Galaxie wiring diagram and the schematic of its electrical system. The detail of each component and its connection with other components are shown on this picture, like the high and low beam, directional signal, parking light, horn and horn relay, generator relay, overdrive relay, coil and distributor, generator, condenser, generator, starter and battery. 

The diagram / schematic below depicts the 1999 Land Rover Defender Td5 Wiring Diagram and Electrical System.

When the ignition key is turned in switch B1 to the STARTING position, it activates the coils of the solenoid (pin 50) of the starter motor A11 and with the voltage coming from the battery A1 (pin 30) supplies the actual starter motor, thus starting the engine.

Note: in vehicle equipped with an anti-theft device the power supply to the starter motor (ignition key in the STARTING position) crosses the anti-theft device control unit N45 which cuts of this power supply in the event of an alarm.(click image to enlarge)

The DC current generated by the alternator A3 is sent to the battery A1 passing through motor A11.

All the power supply lines of the various electrical system on the vehicle start from the branch terminal board G56 connected to the + terminal of the battery A1.

When the alternator does not turn and therefore the battery is not being charged, an earth signal is sent to the instrument panel C10 and illuminates the relative warning light. When the engine is started this signal becomes 12V and the warning light goes out.

If you want to know how to change / replace the 2002 Volkswagen Golf Rear Bumper by yourself, the following picture depicts the 2002 Volkswagen Golf Rear Bumper Parts / Component Diagram.

2002 Volkswagen Golf Rear Bumper Diagram

This is a duplex system that transmits two signals: STP and ST1-.The ECM Uses these signals to monitor the brake, whether or not the brake system is working properly. There ‘s only one signal to be detected at one time, this is either signal which is indicate the brake pedal is being depressed or the signal which is indicate that the brake pedal is being released. If the both signals are detected simultaneously, the ECM intrepets this as a malfunction in the light switch and sets the DTC. The Wiring Diagram below shows the Toyota FJ Cruiser Stop Light Switch Wiring Diagram.

For detailed information about 1997 Audi A4 Air Conditioning System Circuit and Schematic Diagram here (diagram 1 and diagram 2, source: autolib.diakom.ru)

The following schematic shows the 2005 3.5l Chevrolet Colorado Wiring Harness Diagram. This is a car powered by a straight, five cylinders engine or inline-five engine with 3.5L (3,460 cc/211 cu in) total displacement. The bore is 93 mm (3.7 in) and the stroke is 102 mm (4.0 in), this is a straight-five truck engine called the Vortec 350. It has long stroke (the stroke is longer than the bore) for better torque. (click image to enlarge)

LEGEND for the 2005 3.5l Chevrolet Colorado Wiring Harness Diagram:
(1) Accessory Switch C2
(2) Hazard Switch
(3) Accessory Switch C1
(4) Digital Radio Receiver (U2K)
(5) Inflatable Restraint I/P Module
(6) Ambient Light Sensor
(7) Vehicle Communication Interface Module (VCIM) (UE1)
(8) Courtesy Lamp – Footwell Right
(9) Body Control Module (BCM) C2
(10) C201 (I/P Harness to Body Harness)
(11) HVAC Control Module C1
(12) Auxiliary Power Outlet 2
(13) Auxiliary Power Outlet 1
(14) HVAC Control Module C2
(15) Courtesy Lamp – Footwell Left
(16) Data Link Connector (DLC)
(17) C204 (Steering Column Harness to I/P Harness)
(18) C208 (I/P Harness to Body Harness)
(19) C200 (I/P Harness to Body Harness)
(20) Headlamp and Panel Dimmer Switch
(21) Instrument Panel Cluster (IPC)
(22) Radio C1
(23) Radio C2

This is the diagram / schematic that shows the Toyota Camry Serpentine Belt Diagram. A serpentine belt is a belt that drives power steering pump, alternator, water or air pump, A/C compressor or other peripheral devices in automotive engine. There’s only one serpentine belt in one vehicle since this belt is a continuous belt. Below schematic shows the 2002 Toyota Camry Serpentine Belt.

1. Automatic belt tensioner pulley
2. Generator pulley
3. Water pump pulley
4. A/C compressor pulley
5. Crankshaft pulley
6. Power steering pump pulley